BUET VC passes away

Professor Dr. Khaleda Ekram, The first female vice chancellor of Bangladesh University of Engineering & Technology (BUET) passes away on last night approximately at 3.00 AM. ( Inna lillahi wainna ilahi rajiown). She breathed her last at a hospital in Bankok, capital of Thailand. Professor Ekram was appointed as the vice Chancellor of BUET on September 2014. May Allah keep her soul in peace.

Khaleda Ekram, first female vice chancellor of the Bangladesh University of Engineering and Technology (Buet), passed away at a hospital in Bangkok last night.

She was taken to a Bangkok Hospital from Square Hospital on late Friday night by an air ambulance for better treatment.

Her condition was deteriorated since Monday as her kidneys and other organs did not work properly. She was kept on life support.

She was also fighting against leukemia and breathed her last in Thailand at around 3:00am on Tuesday.

Professor Khaleda Ekram of the Architecture Department was appointed as the vice chancellor (VC) of Bangladesh University of Engineering and Technology on September 11, 2014.

Khaleda is the first female vice chancellor of Buet and the second female vice chancellor of the country.

- See more at: http://en.bbarta24.net/national/2016/05/24/2096#sthash.s8Kh1GF8.dpuf

Khaleda Ekram, first female vice chancellor of the Bangladesh University of Engineering and Technology (Buet), passed away at a hospital in Bangkok last night.

She was taken to a Bangkok Hospital from Square Hospital on late Friday night by an air ambulance for better treatment.

Her condition was deteriorated since Monday as her kidneys and other organs did not work properly. She was kept on life support.

She was also fighting against leukemia and breathed her last in Thailand at around 3:00am on Tuesday.

Professor Khaleda Ekram of the Architecture Department was appointed as the vice chancellor (VC) of Bangladesh University of Engineering and Technology on September 11, 2014.

Khaleda is the first female vice chancellor of Buet and the second female vice chancellor of the country.

- See more at: http://en.bbarta24.net/national/2016/05/24/2096#sthash.s8Kh1GF8.dpuf

BREB Assitant Engineer (Mechanical) questions

Bangladesh Rural Electrification Board (BREB) 

Post: Assistant Engineer (Mechanical)

22) Carbide tipped tools usually have

a) Negative rank angle

b) Positive rank angle

c) Any rake angle

d) No rake angle

23) The type of tool used on lathe, shaper and planer is -

a) Single point cutting tool

b) Two point cutting tool

c) Three point cutting tool

d) Multi point cutting tool

24) The process extensively used for making bolts and nuts is

a) Hot piercing

b) Extrusion

c) Cold peering

d) Cold heading

25) Cold working of metal increases

a) Tensile strength

b) Yield strength

c) Hardness

d) All of above

26) Ball bearings are, usually made from

a) Low carbon steel

b) High Carbon steel

c) High speed steel

d) All of the above

27) Cast Iron has

a) High compressive strength

b) Good wear resistance

c) Excellent machinability

28) The Property of a material which enables it to retain the deformation permeability is called

a) Brittleness

b) Ductility

c) Plasticity

d) Malleability

29) The size of gear is usually specified by

a) Pressure angle

b) Pitch Circle diameter

c) Circular Pitch

d) Tooth thickness

30) A spring is used to

a) Measure forces

b) Apply forces

c) Store energy

d) All of the above

31) An universal coupling is used to connect two shafts

a) Which are perfectly aligned

b) Which are not in exact alignment

c) Have lateral misalignment

d) Whose axes intersect at a small angle

32) The material generally used for air-craft components is

a) Mild steel

b) High Speed steel

c) Stainless Steel

d) Aluminum

33 ) The property of a material which enable it to be drawn into the wire with the application of a tensile force, is called

a) Plasticity

b) Elasticity

c) Ductility

d) Malleability

34) The power from the engine to the rear axle of an automobile is transmitted by

a) Worm and worm wheel

b) Super gears

c) Bevel gears

d) Hook’s joint

35) In Mechanical refrigeration system, the refrigerant has the maximum temperature

a) In evaporator

b) Before expansion valve

c) Between compressor and condenser

d) Between condenser and evaporator

36) The amount of radiation mainly depends upon the

a) Nature of the body

b) Temperature of the body

c) Type of surface of the body

d) All of the above

BREB Asstt. Director (HR) Exam Questions

TITAS Civil Engineering Exam Questions

 Titas Gas Transmission and Distribution Company Ltd.

Exam. Date: 19/12/2014

Civil Engineering, Section- A, Total Marks (70)

Venue: MIST

 Answer All Ten questions.

Q.1.   What is cement? Under which condition and requirements cement is superior to
lime.	(7)
Q.2.    a. Write four physical and four mechanical properties of engineering meterials.	(4)
b. What is slum? Draw a slum cone with dimentions.	(3)
Q.3.   As shown in figure below, in the truss, F= 60 Tons and θ = 250 . Find the external	(7)
Reactions (Components at C) and the force member AB and AD.

 

 

Q.4

	a. Define Evaporation, Evapotranspiration and Sodium Adsorption Ratio (SAR)	(4)
	b. Define BOD. Why COD value is higher than BOD?	(3)
Q.5.	Differentiate between:	(7)
	a. Zenith And Nadir
	b. Segregation and Bleeding
	c. Pipe flow and Open channel flow
	d. Duty and Delta of the Crop
Q.6.	Write Short Note:	(7)
	a. Parallux Error
	b. Traverse Surveying
	c. Curb
	d. Flocculation
Q.7.	Explain the following:	(7)
	a. Buckling of Column
	b. Admixure
	c. Development length of reinforcement bar
	d. TMT 500 steel bar

Q.8.   a. Draw qualitative diagram of given size distribution curve and also show the

		(4.5)
Following curve.
1)	Gap Graded
2)	Well Graded
3)	Poorly Graded
b. According to the unified soil classification system specify the meaning of the		(2.5)
following types of soil:
1)	CL
2)	MH
3)	SP
4)	OL
5)	PT

DPDC Assistant Engineer (CE) Questions

Dhaka Power Distribution Company Limited (DPDC) Post: Assistant Engineer (CE)-2014

Exam venue: BUET, Duration: 1.5 hours, Total Marks: 100 Marks 

Marks distribution: 30 marks on General knowledge (60 objectives x 0.5= 30 marks) and 70 marks on departmental questions. 

1. Sedimentation tank design: Volume, discharge given, detention time =?

2. Rain water: Area of roof, rainfall intensity, runoff coefficient given, quantity=?

3. Chlorination curve with break point

4. FM

5. Column area, reinforcement given, tie rod spacing=?

6. SFD, BMD of a simply supported beam and a flexure=?

7. pH given, [OH-] = ?

8. Angle of friction, unit wt, height given, active pressure=?

9. Surveying: length correction of engineering chain=?

10. Concrete volume, ratio given, cement bag =? 
11. Axle load on column determination.

DUET Admission result 2016

The undergraduate admission test of  Dhaka University of Engineering  & Technology (DUET) was held on 19th May 2016. The application submission date started from 31 march 2016 and the deadline was 2nd may 2016. A large numbers of diploma pass students were participated in this exam. There are mainly four faculties Electrical & Electronics Engineering, Mechanical Engineering, Civil Engineering, and Faculty of Engineering .

Masters in Agriculture

Masters in Agriculture in different universities for the Autumn session-2016 is going on. The Bangabandhu Sheikh Mujibar Rahman Agricultural University (BSMRAU)  recently published the notice for masters program in different agricultural subjects for the Autumn session-2016. 

Bangabandhu Sheikh Mujibar Rahman Agricultural University (BSMRAU):

Bangabandu Sheikh Mujibar Rahaman Agricultural University are offering  Masters and Ph.D Program for Agroforestry and Environment, Agro-Processing,Agronomy,  Biotechnology  Crop Botany, Environmental Science , Entomology, Genetics & Plant Breeding, Horticulture, Plant Pathology, Soil Science , Seed Science and Technology, Aquaculture  Fisheries Biology & Aquatic Environment, Genetics and Fish Breeding , Animal Nutrition etc.

 
Eligibility for MS Program: Candidates must have a bachelor degree with a minimum GPA 3.00 (Out of 4.00) from BSMRAU or a bachelor degree with a minimum GPA 3.00 (out of 4.00) from a recognized university/institution.

Engineering Admission Aid

Those who are willing to get admitted in Engineering Universities like BUET, KUET, RUET, MIST, IUT, DUET, CUET , AUST etc  some useful  unit conversions are given here for them.